|
1.0.29
|
Improvement - The LASM will move always be on the infeed side when a board starts
to feed into the saw to keep bent boards from hitting the side of the LASM jaw.
Fixed defect - Multiple exceptions were repaired.
Fixed defect - The CLS data is up to date when first displayed in Diagnostics.
Improvement - The Gripper and LASM are not allowed to move in Diagnostics when the
saw stroke is extended.
Improvement - Servo Diagnostics screens have tightened restrictions for normal users.
|
|
1.0.28
|
Improvement - Changed the length of the elevation servo lock from 60 seconds (or
until the next move) to 0.5 seconds. This change was made to reduce the temperature
of the elevation motor.
Fixed defect - If the blade slows down on a rip and it is the first part cut since
the software has been started an exception was thrown.
Fixed defect - an elevation out of range was caused when trying to cut a coordinated
cut (long cut) when the previous sever angle was less than the current angle.
|
|
1.0.27
|
Improvement - Can cut long scarf cuts that are not on the last part on the board.
Improvement - The LASM would sometimes block the CLS when it shouldn't have.
Improvement - Will now perform 1 or 2 square cuts to cut up trailing waste on a
padded board.
Improvement - Added configuration for the number of printer cards so that print
heads can be turned on/off even if the print cards are installed.
Improvement - Removed the ability to close the calibration screens with the ESC
key.
Improvement - Added Optiflow logging (Mitek-AU customers only).
Fixed defect - The overall length of a keyed-in part could not be entered manually.
Fixed defect -Keyin Parts was showing wrong stock width/thickness for larger sizes.
Fixed defect - The jog amounts were getting zeroed out after a move in Servo Diagonstics.
Fixed defect - In certain cases when the machine was paused at the end of a board
it would not restart properly.
Fixed defect - The CLS could not be turned on/off without restarting the software.
Fixed defect - Unhandled exceptions occured in certain cases.
Fixed defect - Redo board did not have print added when the length of the board
was modified.
Fixed defect - False errors were being displayed when clearing the deck when all
queues are filled.
Fixed defect - The gripper would run out of travel if there was a flat trailing
angle on the last part of the board.
|
|
1.0.26
|
Improvement - Added option in Tools/Options for setting whether a Redo will be first/last
in the cutting list.
Added feature - will remove the blade from a coordinated scarf cut if the saw blade
stalls.
Fixed defect - cls could cause unhandled exceptions if it was disabled while it
was settling.
Fixed defect - angle could drift during calibration if you wait too long after starting
the calibration prior to cutting.
Fixed defect - if redo board was done with the infeed option set to None it would
throw an unhandled exception.
Fixed defect - redo board did not properly place parts when a longer length board
was selected.
Fixed defect - if a beveled part was created from a redo part, the bevel could be
created incorrectly in some cases.
Fixed defect - recovery when a coordinated scarf cut was halted due to the blade
speed slowing did not work properly in some cases.
Fixed defect - the elevation calibration was generating invalid values when the
Crooked Lumber Sensor was enabled.
Fixed defect - if the infeed system has an error, the cutting process was not continuing
properly in some cases.
Fixed defect - wouldn't restart (Continue) properly from a livdeck invalid sensor
condition error.
Fixed defect - a "Blade will intersect LASM" error was generated incorrectly.
|
|
1.0.24
|
Improvement - Will reset ampilifers after an amplifier error to make it possible
to continue from an amplifier error.
Added feature - If the blade slows down, the blade will pull back and retry the
cut.
Improvement - Added Retry, Stop, and Eject buttons to Amp error message.
Added feature - Auto-z pulse.
Added feature - All home positions calibration - can calibrate all servos by cutting
one board.
Improvement - Removed recut option from bevel calibration to allow the board to
be ejected for measurement.
Added feature - Added home position only calibration for each servo.
Improvement - Made changes to reposition the LASM to have enough travel on a long
scarf cut that is not on the last part of the board. The outfeed roller will now
clamp for every trailing cut regardless if the wood is in the roller or not. This
was done because the DistanceToOutfeed roller is conservative and will not clamp
sometimes on short parts.
Fixed defect - metric conversion issues with CLS Diagnostics.
|
|
1.0.23
|
Improvement - Turn off blade after Cut Board completes.
Improvement - Changed the leading waste length that the LASM will carry to the outfeed
roller from 10.5 to 7 because of jamming.
Improvement - Reduce jamming by not releasing the infeed roller on padded trailing
cuts.
Improvement - Coordinated cuts use the tip of the blade to cut instead of being
fully extended.
Fixed defect - the stock was backing up too far which caused the infeed roller and
holdown to fall off the leading edge of the stock.
Fixed defect - Found a problem that caused square cuts on large lumber to become
a coordinated move.
Fixed defect - Cases existed where the bevel cut would be off by 1/4 inch.
Fixed defect - Records were not being deleted from the cutting.mdb database when
a job is deleted.
|
|
1.0.21
|
Added feature - temperature compensation for CLS - call Koskovich for details on
implementation.
Added feature - if a scrap wedge is cut as a long inverse triangle, it will be cut
in half to prevent it from causing a jam.
Added feature - if a trailing pad is too long, it will get cut off prior to making
the trailing cut to prevent it from causing a jam.
Fixed defect - Infeed roller would not always clamp on the leading edge of the board,
causing bevel cuts to be off-center.
Fixed defect - When selecting Reject and Redo Selected Parts on board recovery,
if lumber didn't exist in the lumberyard it would cause an error.
Fixed defect - if there is a loaded board and an in-process board, board recovery
did not handled it correctly - it would eject the loaded board also.
Fixed defect - if the board source is set to None, it would cause an error when
importing a trussfile.
Fixed defect - the gripper was backing up when cutting the last part on a padded
board under lasm control on the first cut.
Fixed defect - in some cases, the square cut would not occur on the last part on
a board.
Fixed defect - short bevels on a padded board could cause a gripper out of range
error.
Fixed defect - if the livedeck is not started, a prompt will appear when a livedeck
command is issued to start it first.
Fixed defect - Cut Board was not clamping the gripper or infeed roller.
|
